• CNC Bent Main Hoop Rolled To Match Factory Valence
• Accepts Most 30" light Bars
• Aggressive Approach Angle
• Precision Welded
• Satin Black Powdercoat
• Grade 8 Hardware
• Crafted In The USA
• Designed for the 2017+ Gen 2 Ford Raptor

 Note: This bumper requires a relocated intercooler

• CNC Bent 
• Precision Welded
• Retains Factory Backup Sensors
• Integrated Trailer Hitch
• Grade 8 Hardware
• Satin Black Powdercoat
  

OVERVIEW:
The SVC Offroad Mojave rear bumper is a plated unit that keeps the same design theme as our Mojave Front Bumper. The Mojave Rear is fully CNC bent and cut to form one seamless unit with an integrated trailer receiver located over 5 inches higher than the factory hitch. This increase in departure angle allows for a more aggressive off-roading and gives the rear of your F150/Raptor a true race inspired look. We engineered the bumper to utilize the factory rear backup sensors and to be as functional as possible. If you're in the market for a sleek bumper that stands out from the rest, look no further than the SVC Offroad Mojave Rear.

• Fits 2017-2020 F-150 Trim Models With 3.5L Or 2.7L Engines
• Larger Core For Lower IAT Temps
• Adaptive Cruise Control Bracket Included
• Relocated Factory Blow-Off Valve To Stay Out of Harms Way When Offroading
• Angled Lower In/Out Ports For Better Clearance Of Frame Cut Bumpers.
• Turbo Clamps
• 100% Manufactured In The USA. 
• Ken Block Tested and Approved
• California Air Resource Board (CARB) Legal 

OVERVIEW:
When set out to design a replacement I/C for the 2017+ Gen 2 Ford Raptor we had 3 sets of criteria that needed to happen:

1. The Intercoolers needed to increase the performance of your truck by reducing IAT temps that robb much needed horsepower pull after pull, which we achieved.  Our Logs have shown reductions of over 20-30 degree temp drops vs. the stock intercooler in our testing. 
2. The I/C needed to work with many frames cut bumpers on the market, not just ours.  We believe we have achieved that.
3. The blowoff valve needed to be relocated up behind the grill so it stays out of the way from debree and hazards when offroading.  Our I/C relocates the factory blowoff valve away from harm for a more secure and trouble-free offroading experience.  

THIS PRODUCT FITS THE FOLLOWING:

• CNC Bent Plate
• Precision Welded and Formed
• Tight Contours 
• 30" light Bar Compatible
• Grade 8 Hardware
• Frame Cut For Massive Approach Angle
• Ken Block Tested and Approved

NOTE: SVC OFFROAD INTERCOOLER MUST BE RUN WITH THIS BUMPER

OVERVIEW:
For years the Raptor bumper market has been swamped with over-designed, to complex-looking plated bumpers that took attention away from the truck, rather than seamlessly blend into the truck as if it was always intended to look that way.  Well, those days are over.  With the introduction of the SVC Offroad Mojave Front Bumper, the status quo has been changed.

The Mojave Front Bumper is the first plate bumper on the market to truly offer a tight, sleek and forward-thinking design to compliment the lines of the 2017+ Gen 2 Ford Raptor.  The approach angle in dramatically increased ensuring safe and bumper digging free nose landings.  The Mojave is crafted right here in the USA, welded and shaped with passion.

If you've been waiting for a plate bumper that doesn't look like an anchor hanging off the front of your Raptor, and are in need of a clean, sleek and stunning front bumper, then we truly believe the Mojave is the bumper for you. 

• Direct Bolt On Replacement 
• Keep Factory Intercooler
• CNC Laser Cut and Bent
• Air Flow Vents For Increased Airflow To Intercooler
• Modular Light Bracket System
• Allows for 30" Light Bar
• Dimple Died Top Plate
• Grade 8 Hardware
• Skid Plate Now Comes Black Powder Coated
• Made In The USA

OVERVIEW
We set out with a vision to make the cleanest looking pre-run bumper on the market for those individuals who want the look of a frame cut bumper, but not actually willing to cut the frame of their new truck. Our 2017+ Gen 2 Ford Raptor Baja Bolt On Bumper is a sleek design that doesn't interfere with the factory intercooler allowing for proper airflow to keep IAT's low, and will still maintain the ability to run a variety of 30" light bars based on our new modular bracket system.

Manufactured right here in the USA with precision and pride.

• Massive Approach Angle
• CNC Bent and Formed
• Securely Shields Electronic Blow Off Valve
• Sleek Design 
• Grade 8 Hardware
• Simple Installation
• Manufactured In The U.S.A.

NOTE: SVCOFFROAD INTERCOOLER MUST BE RUN WITH THIS BUMPER.

OVERVIEW:
When we set out to create our new SVC Offroad 2017+ Gen 2 Ford Raptor Baja Smurf Bumper, we had certain criteria that needed to be met.  The bumper needed to be sleek, lightweight, offer huge approach angles and make sure the relocated electronic blowoff valve is protected behind the skid plate and not out in the open risking possible damage, and thus possible engine damage.

Each one of our Baja Frame Cut bumpers are meticulously CNC bent and radiused to contour the unique front fascia of the 2017-20 Ford Raptor.  This process is time-consuming and difficult, but the end results speak for themselves.  Each one of our bumpers in manufactured right here in the U.S.A. and goes through a rigorous QC inspection.  Each bumper is assembled and welded on a perfectly flat and square fixture table that locates each plate and tube exactly where it needs to be to ensure easy installation and proper gaps.

If you're in the market for a truly amazing crafted and well built front bumper that will transform the look of your truck, look no further.  

Description:

Ford Raptor Fog Light Description

Separate your truck from the pack with the Baja Designs 2017-2020 Ford Raptor “Sportsmen” Fog Light Kit. This kit utilizes four Squadron Sports (3,150 lumens each), and two S2 Sport (1,130 lumens each). This mounting kit includes two Ford-specific mounting brackets and a wiring harness, allowing you to use your factory switch.

Included: 

- (2) Vehicle Specific Mounting Brackets

- Necessary Wiring Harnesses to run lights with factory Auxiliary Switches

- Lights Listed Below

Sportsmen:

• (2) Squadron Sports in Spot
• (2) Squadron Sports in Driving Combo
• (2) S2 Sports in wide Cornering

Description:

Relocates your adaptive cruise control module on your Ford trucks to be compatible with all Addictive Desert Designs front bumpers.

• Fits 2019 Ford Ranger
• Fits 2017 - Up Ford Raptor
• Fits 2015 - Up Ford F-150
• Fits 2017 - Up Ford SuperDuty
• Does not work with Platinum models

15-17' F-150 / 17-Up Raptor Install Instructions

18-Up F-150 Install Instructions

17-Up Super Duty Install Instructions

19 Ranger Install Instructions

Addictive Desert Designs Stealth Fighter front bumper for the Ford Raptor is one of our tightest fitting and most aggressive looking bumpers on the market. Measuring only 1/2" farther from the grille than the factory bumper the Stealth Fighter gives your Raptor a tight fitting steel plate designed bumper.

A modern radius plate design allows the Stealth Fighter to keep a tight fit around the front of your truck to match the factory design, while giving you the added protection of a steel plated bumper. The center of the bumper has a universal light mount system that allows you to mount up to 10 cube lights or a 40" radius LED, or anything in between to give your Ford Raptor the additional lighting setup that you need. Additional mounts for RIGID 10" SR LEDs behind the side panels give your Raptor even more lighting options.

FRAME REINFORCEMENT KIT

Frame reinforcement kit recommended if using D-Rings or Winch. The frame reinforcement kit for the Ford F-150/Raptor gives your OEM frame horns the additional strength they need when using a winch or D-rings. They are fully bolt-on and are compatible with the OEM and all Addictive Desert Designs bumpers. See more

FEATURES

• Modern radius plate design
• Universal center light mount. Up to 10 cube lights or a 40" radius LED.
• Mounts for RIGID 10" SR LEDs on sides
• Fully bolt-on
• Measures only 1/2" farther from grille than factory
• Reinforced clevis mounts
• Designed to accept 3/4" D-Rings

Comes packaged with our Universal Light Mount Kit to install any brand and size lighting combination.

Patented US 9,796,343

ATTENTION: Intercooler Relocation Kit Required

Addictive Desert Designs is proud to add the Race Series R aftermarket bumper to our list of Ford Raptor accessories. The Race Series R front bumper for the Ford Raptor is a form fitting steel tube bumper with an aggressive approach angle.

Radius steel tubes house a center universal light mount system that allows up to a 30" radius LED bar or 8 cube lights. A universal light mount system on top of the bumper allows up to a 40" radius LED bar or 10 cube lights.

Each bumper is designed to be completely bolt-on with no need to cut your truck's frame horns. A slim tucked in design of the Race Series R requires the Ford Raptor Intercooler Relocation Kit in conjunction with this bumper in order for your Ford Raptor to receive proper airflow.

FEATURES

• Formed front tube allows for a tight front end fitment
• Great approach angle with added ground clearance
• .120" wall steel tubing for strength & durability
• CNC laser cut panels ensure precise fitment
• Aluminum paneling helps save weight
• Direct bolt-on

Comes packaged with our Universal Light Mount Kit to install any brand and size lighting combination.

Patented US 9,796,343

PRODUCT DESCRIPTION

Addictive Desert Designs Ford Raptor Stealth Fighter rear bumper is one of the slimmest bumpers you can buy for your Raptor. Measuring the same length from the tailgate as the factory bumper, the Stealth Fighter adds protection to your truck without adding bulk and size.

A unique style with sharp angles and recessed paneling follows the factory dovetail look and allows use of factory features such as parking sensors, tow hooks, and hitch. The Stealth Fighter comes standard with two rear face cube light mounts to give your truck additional lighting.

FEATURES

• Sleek design fits tight to the truck
• Compliments factory dovetail styling
• Mounts for two rear facing cube lights
• Retains factory tow hooks and dual exhaust
• Compatible with factory backup sensors
• Built with steel plating for add strength
• Measures same distance from tailgate as factory bumper
• Backup Sensor cutouts
• Bumper Color: Hammer Black
• Panel Color: Satin Black
• Cube Light Mounts

Install Instructions

• Hammer black powder coat finish
• Satin black powder coat panel finish
• Mounts for cube lights

• Bumper Color: Hammer Black
• Panel Color: Satin Black
• Center Mount: 20" Radius Light Bar / Up to 7 Cube Lights / Universal Mounts

• Requires Adaptive Cruise Control relocation bracket for adaptive cruise control equipped vehicles
• Hammer black powder coat finish
• Satin black powder coat panel finish
• Universal light mount for up to 6 cube lights or 20" radius light bar

PRODUCT DESCRIPTION

The Addictive Desert Designs Bomber rear bumper features a clean, modern look. The plate steel construction offers strength, while remaining low profile. The angles meet perfectly with the body lines of the vehicle to make it look as though it was there from the factory.

Give your Ford Raptor additional lighting with the two standard rear facing cube light mounts. Factory amenities such as parking sensors, tow hitch, and dual exhaust are all retained. As always, this product is fully bolt-on and made in America.

FEATURES

• Modern plate steel design
• Compliments factory dovetail styling
• Mounts for two rear facing cube lights
• Retains factory tow hooks and dual exhaust
• Compatible with factory backup sensors
• Made in America
• Backup sensor cutouts
• Hammer black powder coat finish
• Satin black powder coat panel finish
• Mounts for cube lights

Install Instructions